- APPS
- Shop Floor Control - Quality 19.0
| Lines of Code | 2034 |
| Technical name | viin_mrp_workorder_quality |
| License | OPL-1 |
| Website | https://viindoo.com/apps/modules/19.0/viin_mrp_workorder_quality |
| Read description for | v 18.0 |
| Required Apps | Manufacturing (mrp) Discuss (mail) Employees (hr) Inventory (stock) |
| Included Dependencies | Shop Floor Control Manufacturing Quality Control Viindoo Manufacturing Stock Quality Control Web Gantt Quality |
Quality results recorded at the machine, by the person who did the check
For manufacturers whose operators run work orders on a touch screen at the work center
Record work order quality checks on the Shop Floor tablet before a job starts and finishes.
Odoo Community Edition · Viindoo Cloud · License OPL-1 · English, Vietnamese
Extends Shop Floor Control: the quality steps join the job board, the operation screen and the closing screen.
Extends Manufacturing Quality Control: the same checks and holds, recorded on the tablet.
What changes for your team
Results recorded where the check is done
The operator measures at the machine, writes the reading on paper and someone types it in later, if at all.
→ Each quality step sits on the job's own screen. The reading goes in on the number pad with the target and tolerance in view, and gets the same verdict as at the desk.
No job runs past an open check
A job is started or finished while its checks are still open, and nobody notices until the goods are made.
→ A check still to do turns Finish operation off and writes the reason under it, while Pause stays usable. A held job opens the checks left before Start.
The order closes once its final checks are recorded
The order is closed at the end of the shift and the final inspection is left for later.
→ The finished product checks sit on the closing screen. The order cannot close while one is to do or a blocking one has failed; recording the output is never held.
Features
Record at the machine
- ✓ Every quality step of the operation on the job's screen, with what is left
- ✓ Pass or Fail in one touch, with an optional note on a Fail
- ✓ Measurements on the number pad, target and tolerance in view
- ✓ Photo evidence from the device camera
- ✓ Scorecards graded one criterion card at a time
- ✓ Mark as done for a step without a verdict
Hold the work
- ✓ Each job board card shows where quality stands
- ✓ A job held by quality opens the checks left before Start
- ✓ Finish turns off with its reason; Pause stays usable
- ✓ Finished product checks recorded on the closing screen
Report and correct
- ✓ Raise a quality alert from a step without leaving the job
- ✓ Reopen a step recorded by mistake, where the user may
- ✓ Waivers and concessions stay a Quality User's desk decision
Analyse by person
- ✓ Quality checks grouped by the operator credited and their crew
- ✓ Quality alerts listed in Shop Floor Entries, grouped by employee
Built for daily use
- ✓ Anyone allowed to work on the operation records its checks
- ✓ Recording the output is never held by a check
- ✓ After a lost connection, Retry records the result once
Ready on day one
Nothing to configure in this module
It installs by itself when Shop Floor Control and Manufacturing Quality Control are both installed. The steps on the tablet come from the control points the Quality app already holds.
What you set up first
Control points on the operation, the access right of each person, and each operator's user linked to an employee; the Documentation tab covers each step.
Before you decide
Do operators need a Quality access right?
No. Anyone allowed to work on the operation records its checks. Waiving a check or accepting a failed one stays a desktop decision of a Quality User, and only a Quality User reopens a Failed or Waived step; the screen says who acts next.
Will it stop production for nothing?
Only a check still to do, or a failed check of a No Proceed if Failed control point, holds the start, the finish or the closing. Pause stays usable and recording the output is never held.
What if the Wi-Fi drops at the machine?
The step says it is not sure the result was recorded and offers Retry. Retry sends it again and the result is recorded once.
Does the tablet agree with the quality team's desk?
Yes: the same reading gets the same verdict at both. One limit: a closing screen left open does not refresh by itself after a Quality User decides at the desk; open it again to see the decision.
What does it take to install and run?
Shop Floor Control and Manufacturing Quality Control; no extra Python package or server program. To start an operation on the tablet, the user must be linked to an employee. Results stay in your own database; the module calls no outside service.
Try it, then ask us
Read the Documentation tab above, then try the live demo: v19demo-int.viindoo.com
Pre-sales & partnership
viindoo.com/contactusTechnical support
viindoo.com/ticketShop Floor Control - Quality
Note
Extends viin_mrp_workorder - see its documentation.
Note
Extends to_quality_mrp - see its documentation.
Who this guide is for. Machine operators (access right Manufacturing / User), Quality Users (Quality / User), manufacturing supervisors (Manufacturing / Administrator) and the administrator who sets the module up.
Shop Floor Control - Quality brings the quality checks of a work order onto the same touch screen the operator already uses to run the job. The operator records Pass, Fail, a measurement or a photo at the machine, at the moment of the check, so the result comes from the person who really did it. A job cannot start while the checks of its components are still to do or a blocking check has failed, an operation cannot be finished while one of its checks is still to do or a blocking check has failed, and a manufacturing order cannot close while a finished product check is still to do. Recording the output is never blocked, and the screen tells the operator what holds a step and who acts next before the tap.
The module installs by itself when both Shop Floor Control and Manufacturing Quality Control are installed. It adds no menu of its own: the quality steps appear inside the Shop Floor app. What the quality steps, control points and quality alerts mean is explained in the documentation of Manufacturing Quality Control and Quality; what the job board, the operation screen and the closing screen do is explained in the documentation of Shop Floor Control.
The screenshots show the demo company: Marc Demo is the machine operator, Mitchell Admin acts as the Quality User, and the products, a Bench and a Stool, are invented for this guide.
Overview
A job passes through quality in four stages. Each stage has one person who acts and one hand-off.
- Ready, held by quality. The operator opens the job, records the quality steps of the operation and starts it. Only a failed step of a control point with No Proceed if Failed hands the job to a Quality User.
- Blocked by a failed check. The Quality User reopens the step, or decides on the desktop what happens to the goods, and the job goes back to the operator.
- Running. The operator records the output and finishes the operation. A check that is still to do holds Finish operation, never the output.
- Closing the order. The operator records the finished product checks on the closing screen and closes the order. The supervisor reads the results afterwards, by worker and by crew.
| Role | What they do | Access right to assign |
|---|---|---|
| Machine operator | Records the quality steps, the finished product checks and the quality issues on the tablet; reopens a step recorded by mistake. | Manufacturing / User |
| Quality User | Reopens a Failed or Waived step; waives a check or accepts a failed one with conditions on the desktop. | Quality / User |
| Manufacturing supervisor | Groups the quality checks and the shop floor entries by worker and by crew. | Manufacturing / Administrator |
| Administrator | Installs the apps, gives each person their access right, links users to employees and defines the control points with the Quality Administrator. | Role / Administrator |
Setup (for the Administrator)
Installation
- Open Apps.
- Search for Shop Floor Control - Quality.
- Click Install.
You normally do not need to do this. The module is installed automatically as soon as Shop Floor Control and Manufacturing Quality Control are both installed. If one of them is missing, install it first, then check that the module is in the list of installed apps.
Access rights
Open Settings ‣ Users & Companies ‣ Users, open the user and use the tab Access Rights.
- Give each machine operator the access right Manufacturing / User. Operators see the Shop Floor app, the quality steps of their jobs, Quality ‣ Quality Control ‣ Quality Controls ‣ Quality Checks and their own lines in Manufacturing ‣ Reporting ‣ Shop Floor Entries.
- Give each Quality User the access right Quality / User. Only a Quality User can reopen a step recorded as Failed or Waived, and only a Quality User waives a check or accepts a failed one with conditions - on the desktop.
- Give each supervisor the access right Manufacturing / Administrator, which also shows every line of Shop Floor Entries.
Employees
Link the user of each operator and Quality User to an employee: on the employee, open the tab Settings and fill User. A user who is not linked to an employee cannot start an operation on the tablet. Each result recorded on the tablet keeps the employee credited for it and the department of that employee at that moment.
Control points
The quality steps on the tablet come from the control points you define in the Quality app. Nothing is configured in this module itself.
Open Quality ‣ Quality Control ‣ Quality Controls ‣ Control Points and click New.
Enter a Title. This is the name the operator reads on the tablet.
Choose the Test Type: Pass - Fail, Measure, Take a Picture or Scorecard. Each step shows exactly the controls its type allows.
In Products (or Product Templates), choose the product to check. For a check done during the operation, choose a component of the bill of materials. For a check of the finished product, choose the finished product.
In Operation Types, choose the operation type that applies, for example Manufacturing.
In Responsible, choose the person the check is assigned to. It is shown on the form and in the lists of the checks, but anyone allowed to work on the operation can record the check on the tablet.
Tick No Proceed if Failed if a failed result must stop the work until a Quality User releases it.
For a Scorecard control point, choose the scorecard that lists the criteria. For a Measure control point, also enter the norm, its unit and the tolerance range. The tablet shows them next to the numpad, and the verdict is the same as at the desk. On the tab Message If Failure of any control point you can write a short instruction that the tablet shows on the step when the result is Failed.
The checks are created when the manufacturing order is confirmed:
- A control point on a component gives a step on the work order of the operation where that component is used in the bill of materials.
- A control point on the finished product gives a finished product check on the manufacturing order. It appears on the closing screen, not on an operation.
Machine operator: record the quality checks of your job
Record the quality steps before you start
When a job has quality steps to do, its card on the job board says so and the card does not start the job. Open the card, record every step, then start.
Open the Shop Floor app, choose your work center and click Open job board.
Look at the card of the job:
- A yellow tag such as 4 quality check(s) to do first, the button Open & do quality checks and the line that names the checks mean that the job is held by quality.
- Quality passed and the button Open & start mean that nothing holds the job.
- Quality check failed means that a step is Failed. When the failed step has No Proceed if Failed, the button reads Open quality checks and the job cannot start.
Tap Open & do quality checks. The screen Quality checks before you start lists every step with its status (To do, Passed, Failed or Waived) and a count such as 4 step(s) still to record. Start the operation stays grey, and the reason is written under it.
On a Pass - Fail step, tap Pass if the result is good. The status changes to Passed and the count goes down.
On a Measure step, read the target and tolerance (for example Target 10.00 mm, tolerance 9.50 - 10.50), tap Enter measurement, type the reading on the numpad and tap Confirm. The step shows the value with its unit and the verdict (Passed or Failed) that the tolerance gives.
On a Take a Picture step, Pass stays greyed out until a photo exists. Tap Take photo, take the picture with the tablet camera, check the thumbnail and the message Photo ready - tap Pass or Fail, then tap Pass. The step then shows 1 photo(s) on this step. If the picture is not good, tap Retake photo.
When no step is left to do, Start the operation becomes active. Tap it. The job moves to Running and its screen lists the same steps under Quality steps.
Note
On the job board, tapping the card only opens the job. The job starts only when you tap Open & start or Start the operation.
Grade a scorecard step
A step of the type Scorecard shows one card per criterion.
On each card tap Pass, Fail or Not Applicable. A criterion marked Must Pass fails the whole step when it is graded Fail. The line under the cards shows the score and the score needed to pass.
When every criterion is graded, Confirm becomes active. Tap it. The step shows Passed or Failed according to the score, exactly as the desk gives for the same grading.
A confirmed step shows its grading and offers no grade. Tap Reopen to grade it again.
Raise the alarm on a defect
Anyone allowed to work on the operation records its steps, whoever is named in the Responsible field of the control point. You can report a defect that you see, like pulling an andon cord, with the Fail button.
Tap Take photo and photograph the defect. The message Photo ready - tap Fail to send it appears.
Tap Add a note to the Fail and describe the problem in What is wrong? (optional). The note is optional, and the keyboard opens only when you ask for it.
Tap Fail. The step shows Failed and 1 photo(s) on this step. The Responsible of the step does not change, and your name is kept as the person who recorded the result.
To add more evidence, tap Add photo on the Failed step. The photo is added at once and the count grows, for example 2 photo(s) on this step. You can add photos to a Failed step, but you cannot remove or replace them.
A Fail on a control point that does not have No Proceed if Failed does not hold the job: when nothing else is left to do, Start is active, as in the screenshot above. The card of the job shows Quality check failed and the Quality team sees the Failed step.
A failed blocking step stops the job
When the control point has No Proceed if Failed, a Fail needs your confirmation, because it stops the work on the operation.
On the step, optionally tap Add a note to the Fail and describe the problem.
Tap Fail. The question Record Fail on <step>? opens, with the warning that a failed result stops the work on the operation until it is resolved.
Tap Record Fail to confirm, or Cancel if you tapped by mistake.
The step shows Failed with the failure message of the control point. Start the operation is disabled, and the reason names the failed check and says that a Quality User has to reopen it or decide what to do with the defective goods. Your Reopen button is greyed out with the sentence A Quality User reopens this step or decides what to do with it.
The job still opens. You can tap its card again to read why Start the operation is off, instead of meeting a dead end. Ask a Quality User.
Reopen a step you recorded by mistake
If you tapped Pass on the wrong step, or typed the wrong reading, you can take it back, as long as the step is Passed and you may record it.
Open the Quality steps of the job and find the step.
Tap Reopen. The step goes back to To do and the line 3 step(s) still to record counts it again. The employee and the crew credited for the result are cleared; photos already on the step stay.
Record the right result.
Once a step is Passed, it offers you Fail (with Add a note to the Fail), Report quality issue and Reopen, and no second Pass. A Measure step that is Passed offers no new reading: tap Reopen first, then enter the reading again.
A Failed or Waived step is different: only a Quality User can reopen it. For you the button is greyed out and the screen says so.
A step the tablet cannot move
A Quality User can waive a check that does not apply, or accept a failed step with conditions. These decisions are made on the desktop, never on the tablet. A Waived step shows its status, and a failed step accepted with conditions shows Decision: Concession. A waived step no longer counts in step(s) still to record. For both, the sentence beside Reopen says that a Quality User is the one who acts next.
A step with no verdict
Each step offers the controls its test type can do, read from the capabilities of the type and not from its name. A step whose type offers no Pass, Fail or measurement shows the description of the type and the button Mark as done; a Scorecard step shows Confirm instead. Report quality issue and Reopen are offered on every step.
When Finish is off
While a check of the operation is still to do, or a failed check blocks the work, Finish operation is greyed out and the reason is written under the buttons. Pause stays usable. Record the check on the same screen: when it is recorded, Finish operation becomes active again. If a failed check is the reason, ask a Quality User to reopen it or to decide what to do with the defective goods. Any other reason that holds the operation, such as materials still to record, is written there too.
Report a quality issue
When something is wrong but it is not a result for one step, raise a quality alert without leaving the job.
On the step, tap Report quality issue.
The step shows Quality issue reported. and the head of the Quality steps shows 1 quality alert(s) on this operation. The alert gets a summary from the step: its title and its product, for example Photo of rail face - Bench Rail. If you tap twice on a slow connection, only one alert is created.
The alert is also listed in Manufacturing ‣ Reporting ‣ Shop Floor Entries. Open the list and look at the column Kind: the line reads Quality Alert, next to the production, consumption and close order lines. You can group the lines by Credited Employee. The quality team handles the alert in the Quality app.
If the job has no failed check and nothing to do, its card on the job board can show a chip such as 1 quality alert(s). A deliberate second tap on Report quality issue, once the first alert exists, can create a second alert for the same step.
Check the finished product and close the order
The finished product checks of the order are recorded on the closing screen. Recording the output is never blocked by quality.
On the job, record the materials used and tap Record output as usual. Enter the quantity just made.
Tap Finish operation. The screen Confirm Closing the Production Order opens (on the job board the card of a finished last operation offers Close the order).
Under Finished product checks, each check shows its status. While a check is to do, the button Confirm closing order <order> is disabled and the sentence under it names the checks that are still to do and says that you can record them, or ask a Quality User to waive them.
Tap Pass on the check. The hold sentence goes and the button becomes active. Tap Confirm closing order <order>.
The banner Order closed with 1.00 Units produced. confirms the closure. Tap Done.
If a finished product check with No Proceed if Failed has been recorded as Failed, the closing controls stay off and the sentence says that a Quality User has to reopen the check or decide what to do with the defective goods before the order can close. An open closing screen does not update by itself when a Quality User decides on a check in the back office: it shows the state the checks had when it was opened. Once the order is closed, its finished product checks are listed with their status and nothing to tap: no verdict, reading, photo or Reopen. A refusal on a closed order names the order.
When the connection drops
If the Wi-Fi is lost when you tap Pass or Fail, the tablet cannot be sure that the result was saved. Nothing is lost and nothing is recorded twice.
A band appears on that step: Not sure it was recorded - the network connection was lost. What you entered is still here; check the Wi-Fi, then tap Retry - nothing will be recorded twice. The step is still To do.
Check the Wi-Fi, then tap Retry. The same result is sent once and the step shows Passed (or Failed).
Use it on a phone
The same screens work on a phone. The steps stack in one column, and the buttons keep their reasons: a Reopen that is greyed out for you says who acts next, and the reason Start the operation is off is written under the button.
Quality User: release a failed or waived step
A Quality User, with the access right Quality / User, can reopen a step that the operator recorded as Failed, or a step that is Waived. Waiving a check that does not apply and accepting a failed step with conditions are done on the desktop, in the Quality app.
Open the Shop Floor app on your tablet, choose the work center and open the job board. A card with a blocking failed check shows the tag Quality check failed and the button Open quality checks.
Open the card. On the Failed step you see the failure message, and Reopen is active for you.
Tap Reopen. The step goes back to To do and nobody is kept as having checked it; the worker and the crew credited for the result are cleared with it.
Inspect the product, then tap Pass (or Fail) to record the verdict. When nothing else holds the job, the operator can tap Start the operation.
You can also record the finished product checks on the closing screen with the same buttons. The order closes once they are Passed.
On a step that is already Passed, the Quality User keeps Pass (a repeat Pass records the step anew), Fail, Reopen and, on a Measure step, the reading. The operator is offered only Fail, Report quality issue and Reopen there.
Manufacturing supervisor: analyse the checks by worker and crew
Each result recorded on the tablet keeps the employee credited for it and the department of that employee at that moment, even if the employee changes department later. A result recorded at a desk has neither.
Open Quality ‣ Quality Control ‣ Quality Controls ‣ Quality Checks and switch to the list view.
In the search options, under Group By, choose Shop Floor Operator and then Crew, next to the groupings by work center, work order, manufacturing order and Checked By. The two columns Shop Floor Operator and Crew can also be shown from the optional columns of the list, and the two fields are searchable.
In Manufacturing ‣ Reporting ‣ Shop Floor Entries, group the lines by Credited Employee to see the quality alerts raised on the tablet with the other entries of each employee.
Troubleshooting
- Start the operation is greyed out. Read the sentence under the button. It lists the checks to do, or the failed checks that block the step. Record the checks, or ask a Quality User to waive them or to reopen a failed one.
- Pass is greyed out on a photo step. A photo step needs a photo for a Pass. Tap Take photo first.
- There is no Pass on a step I already passed. A Passed step offers you Fail, Report quality issue and Reopen. To record the result again, tap Reopen first.
- Reopen is greyed out. A Failed or Waived step can be reopened only by a Quality User. The sentence beside the button says who acts next.
- I tapped the card and the job did not start. This is intended. Tap Open & start or Start the operation.
- The quality steps do not appear on the job. Check that the control point has the right product (a component of the bill of materials used in this operation), the right operation type and that it was created before the order was confirmed. The steps are created when the order is confirmed.
- The Retry band appears. The connection was lost. Check the Wi-Fi and tap Retry.
- I cannot start an operation on the tablet. The user must be linked to an employee, on the tab Settings of the employee. Ask the administrator.
- The closing screen still shows a check to do after a Quality User decided on it. An open closing screen does not update by itself: it shows the state the checks had when it was opened.
FAQ
- Can an operator record a Pass for a step that names someone else as Responsible?
- Yes. The Responsible is the person the check is assigned to; anyone allowed to work on the operation can record it, and the result keeps who recorded it.
- What happens when a Fail is recorded on a control point without No Proceed if Failed?
- The step shows Failed and the Quality team sees it, but it does not hold the job or the closing of the order.
- Can I remove a photo from a Failed step?
- No. You can add photos to a Failed step, but not remove or replace them.
- Does quality block the recording of the output?
- No. Only the start and the finish of the operation and the closing of the order are held.
- Why is the finished product check not on the operation screen?
- It belongs to the manufacturing order, not to an operation. It is recorded on the closing screen, and it does not hold the start of any operation.
- Can a Quality User waive a check on the tablet?
- No. Waiving a check and accepting a failed one with conditions are done on the desktop. The tablet shows the decision and who acts next.
- Can I change a finished product check after the order is closed?
- Not from the tablet. A closed order lists its finished product checks without any control.
- Where can I see the quality alerts raised from the tablet?
- In Manufacturing ‣ Reporting ‣ Shop Floor Entries (kind Quality Alert) and in the Quality app.
This software and associated files (the "Software") may only be used (executed, modified, executed after modifications) if you have purchased a valid license from the authors, typically via Odoo Apps, or if you have received a written agreement from the authors of the Software (see the COPYRIGHT file).
You may develop Odoo modules that use the Software as a library (typically by depending on it, importing it and using its resources), but without copying any source code or material from the Software. You may distribute those modules under the license of your choice, provided that this license is compatible with the terms of the Odoo Proprietary License (For example: LGPL, MIT, or proprietary licenses similar to this one).
It is forbidden to publish, distribute, sublicense, or sell copies of the Software or modified copies of the Software.
The above copyright notice and this permission notice must be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.